Product Description

Mandrel of Pay-off Reel and Tension Reel

For hot rolling 
The mandrel is the key part of hot rolling tension reel for coils. Coiling temperature is between 550 to 850ºC. The mandrel has mainly 2 types: link wedge type and double wedge type.

Link wedge type can also be divided into 2 kinds: link wedge-coupling drive and link-spline drive.

For link wedge-coupling type tension reel, the mandrel is mainly composed of mandrel body, spreader bar, segment, link, wedge and spreading cylinder. Spreader bar has multistage slopes and segment is supported by multistage wedge. Segment is connected with spreader bar by link so segment does not drop off. With compression spring in the middle of wedge, wedge can firmly contact segment and pyramid surface. There is a gap between the upper surface of wedge and segment, which can reduce the impact of coil head to mandrel during coiling coil. Mandrel body is installed on 2 bearings. Power is transmitted by crowned-teeth coupling in the real. It is very convenient to dismantle, and due to there is no gear impact during working, mandrel rigidity is improved. It’s very beneficial to control the dynamic tension.

The spreading principle of mandrel: spreader bar moves inside mandrel body in axial direction dreivern by hydraulic cylinder, the slant of sperader bar pushes the wedge inside radial hole of mandrel body to move outward. The wedge surface pushes segment to expand outward. Wedge diameter will expand. After coiling coils, spreader bar moves in the opposite direction driven by hydraulic cylinder, and pulls segment to shrink through link. Wedge moves inward and mandrel diameter becomes smaller to discharge state. Then you can begin to discharge coil.

For the 2 types of link wedge-coupling drive and link wedge-spline drive, the mandrel structures and principles are almost same and the main difference is drive type of mandrel. For link wedge-spline drive type, connection between mandrel and main transmission cases is spline, i.e. insert type. When mouting and dismantling, mandrel can be directly inserted or pulled out of the main transmission cases to achieve the rapid replacement.
The main driving motor drives gear shaft rotation through the intermediate shaft. The gear shaft dirves big gear rotation, and the big gear drives mandrel rotation through spline.

For the double wedge type tension reel, the mandrel is mainly composed of mandrel body, spreader bar, segment, spreader wedge, buffer wege and hyd. Cylinder.

The spreading principle of double wedge type mandrel: hyd. Cylinder makes spreader bar move back and forth in axial direction and the wedge move in radical direction. So the segment becomes big. T-hook on spreader bar pulls wedge back and the hook outside the wedge pulls segment back. This will make the manderel small. With spline connectiion for power transmission unit, mandrel can be rapidly replaced. Cooling water channel inside the mandrel, so cooling effect is good. Lubricant can be injected by auto and manual type, so it can reduce parts wear.

Pay-off reel and tension reel for cold rolling coils are used in cold rolling production line or pay-off when acid pickling,galvanization,annealing,shear,coating or coil tension in out let.
Cold rolling mandrel is the key part of pay-off reel and tension reel. According to different structure, it has beam wedge type, pyramid axis type, pyramid sleeve type, wedge type, radial direction hydraulic cylinder type, etc. Or simply, open type and close type. The close type mandrel is a close circle without gap in the surface after expanding.it is suitable for coiling thin strip steel. The open type mandrel means there is a gap between segments after mandrel expanding, suitable for coiling thicker strip steel.
 
For cold rolling
Pay-off reel and tension reel for cold rolling coils are used in cold rolling production line or pay-off when acid pickling, gavanization, annealing, shear, coating or coil tension in outlet.

Cold rolling mandrel is the key parts of pay-off reel&tension reel. According to different structure, it has beam wedge type, pyramid axis type, pyramid sleeve type, wedge type, radial direction hydraulic cylinder type, ect. Or simply, open type and close type. The close type mandrel is a close circle without gap in the surface after expanding. It is suitable for coiling thin strip steel. The open type mandrel means there are a gap between segment after mandrel expanding, suitable for coiling thicker strip steel.

The beam wedge type mandrel is mainly composed of the main shaft, expanding core, segment, axial direction wedge, radial direction wedge and spreading cylinder, etc. There are 2 kinds of structure: with jaw or without jaw. The mandrel with jaw is used for coiling thicker strip steel. It can also be set with steel sleeve or paper sleeve to coil with belt wrapper. The mandrel without jaw is used for coiling thin strip steel by belt wrapper.

The mandrel will move along axial direction driven by the expanding core & wedge block, through relative sliding between the wedge block and segment, swelling and shrinking will occur in radial direction, reset by spring.

The pyramidal axis type mandrel is divided into tapper type and back taper type according to the tilting direction of axis slope. This mandrel has simple structure ,less parts, large main shaft section and high strength .So it can bear large tension, not only coiling ,but also uncoiling. There are 2 kinds of structure: with jaw or without jaw .it’s mainly consisted of the pyramid axis, segment, hollow sleeve and spreading cylinder, etc.

Presently, the back taper type mandrel is the most popular. The oil goes into the cylinder via a rod cavity. The cylinder pulls the pyramidal shaft backward along axial direction and push segment to expand outside, so the drum is expanded. Pyramidal axis moves back ward along axial direction, and segment is pulled back by the T-key, thus the mandrel is shrinked.

KMD introduction:

Location: HangZhou
Established year: 1997
Staffs: 800
Engineer members: 180

Main lines: Electromagnetic liftings, electromagnetic sirrers, magnetic separators, Cable reels, Mandrels, Oil film bearing seat, etc.
Export countries: over 40 countries including Vietnam, Pakistan, Phillipines, India, Korea, Myanmar, Laos, Thailand, Mylaysia, Russia, Ukrain, Indonesia,  Turkey,  Spain, USA, etc.
Certifications: CE, ISA, ISO9001
Applications: Metallurgy, Electricity, Mining, Cement industry, Sugar industry, Food, Building materials, Traffic, Light industry, etc.

Welcome to visit our factory!!

Exhibition all over the world

Clients

Xihu (West Lake) Dis.d by managing conception as
Xihu (West Lake) Dis.d the direction by advanced technology,
Exploited the market by perfect service
Building the reputation by excellent quality.

FAQ

Q1.Are you factory?
Yes. We are lifting electromagnet factory, and we also factory for electromagnet stirrer, control cabinet, cable reel, electromagnetic separator, and mandrel since 1997. With 23 years history our clients are more than 2000, and export more than 50 countries. Our plant area is more than 60,000 square meters.

Q2.How fast can i get the quotation?

A: We usually quote within 24 hours after we get your inquiry.If you are very urgent to get the price, please call us or tell us in your email so that we will regard your inquiry priority.

 

Q3. What’s your payment terms?
A: T/T, DP or L/C AT SIGHT for first cooperation..

 

Q4.Can I get sample before order? 
A: Yes, of course. After price confirmation, you can require for samples to check our quality, but the freight is on your site.
 

Q5. Do you accept OEM?

A: Yes. We accept custom design OEM.
 

Q6. How do you make our business long-term and good relationship?

A: 1. We keep good quality and competitive price to ensure our customers benefit;

 2. We respect every customer as our friend and we sincerely do business and make friends with them, no  matter where they come from.

 

Types of Splines

There are 4 types of splines: Involute, Parallel key, helical, and ball. Learn about their characteristics. And, if you’re not sure what they are, you can always request a quotation. These splines are commonly used for building special machinery, repair jobs, and other applications. The CZPT Manufacturing Company manufactures these shafts. It is a specialty manufacturer and we welcome your business.
splineshaft

Involute splines

The involute spline provides a more rigid and durable structure, and is available in a variety of diameters and spline counts. Generally, steel, carbon steel, or titanium are used as raw materials. Other materials, such as carbon fiber, may be suitable. However, titanium can be difficult to produce, so some manufacturers make splines using other constituents.
When splines are used in shafts, they prevent parts from separating during operation. These features make them an ideal choice for securing mechanical assemblies. Splines with inward-curving grooves do not have sharp corners and are therefore less likely to break or separate while they are in operation. These properties help them to withstand high-speed operations, such as braking, accelerating, and reversing.
A male spline is fitted with an externally-oriented face, and a female spline is inserted through the center. The teeth of the male spline typically have chamfered tips to provide clearance with the transition area. The radii and width of the teeth of a male spline are typically larger than those of a female spline. These specifications are specified in ANSI or DIN design manuals.
The effective tooth thickness of a spline depends on the involute profile error and the lead error. Also, the spacing of the spline teeth and keyways can affect the effective tooth thickness. Involute splines in a splined shaft are designed so that at least 25 percent of the spline teeth engage during coupling, which results in a uniform distribution of load and wear on the spline.

Parallel key splines

A parallel splined shaft has a helix of equal-sized grooves around its circumference. These grooves are generally parallel or involute. Splines minimize stress concentrations in stationary joints and allow linear and rotary motion. Splines may be cut or cold-rolled. Cold-rolled splines have more strength than cut spines and are often used in applications that require high strength, accuracy, and a smooth surface.
A parallel key splined shaft features grooves and keys that are parallel to the axis of the shaft. This design is best suited for applications where load bearing is a primary concern and a smooth motion is needed. A parallel key splined shaft can be made from alloy steels, which are iron-based alloys that may also contain chromium, nickel, molybdenum, copper, or other alloying materials.
A splined shaft can be used to transmit torque and provide anti-rotation when operating as a linear guide. These shafts have square profiles that match up with grooves in a mating piece and transmit torque and rotation. They can also be easily changed in length, and are commonly used in aerospace. Its reliability and fatigue life make it an excellent choice for many applications.
The main difference between a parallel key splined shaft and a keyed shaft is that the former offers more flexibility. They lack slots, which reduce torque-transmitting capacity. Splines offer equal load distribution along the gear teeth, which translates into a longer fatigue life for the shaft. In agricultural applications, shaft life is essential. Agricultural equipment, for example, requires the ability to function at high speeds for extended periods of time.
splineshaft

Involute helical splines

Involute splines are a common design for splined shafts. They are the most commonly used type of splined shaft and feature equal spacing among their teeth. The teeth of this design are also shorter than those of the parallel spline shaft, reducing stress concentration. These splines can be used to transmit power to floating or permanently fixed gears, and reduce stress concentrations in the stationary joint. Involute splines are the most common type of splined shaft, and are widely used for a variety of applications in automotive, machine tools, and more.
Involute helical spline shafts are ideal for applications involving axial motion and rotation. They allow for face coupling engagement and disengagement. This design also allows for a larger diameter than a parallel spline shaft. The result is a highly efficient gearbox. Besides being durable, splines can also be used for other applications involving torque and energy transfer.
A new statistical model can be used to determine the number of teeth that engage for a given load. These splines are characterized by a tight fit at the major diameters, thereby transferring concentricity from the shaft to the female spline. A male spline has chamfered tips for clearance with the transition area. ANSI and DIN design manuals specify the different classes of fit.
The design of involute helical splines is similar to that of gears, and their ridges or teeth are matched with the corresponding grooves in a mating piece. It enables torque and rotation to be transferred to a mate piece while maintaining alignment of the 2 components. Different types of splines are used in different applications. Different splines can have different levels of tooth height.

Involute ball splines

When splines are used, they allow the shaft and hub to engage evenly over the shaft’s entire circumference. Because the teeth are evenly spaced, the load that they can transfer is uniform and their position is always the same regardless of shaft length. Whether the shaft is used to transmit torque or to transmit power, splines are a great choice. They provide maximum strength and allow for linear or rotary motion.
There are 3 basic types of splines: helical, crown, and ball. Crown splines feature equally spaced grooves. Crown splines feature involute sides and parallel sides. Helical splines use involute teeth and are often used in small diameter shafts. Ball splines contain a ball bearing inside the splined shaft to facilitate rotary motion and minimize stress concentration in stationary joints.
The 2 types of splines are classified under the ANSI classes of fit. Fillet root splines have teeth that mesh along the longitudinal axis of rotation. Flat root splines have similar teeth, but are intended to optimize strength for short-term use. Both types of splines are important for ensuring the shaft aligns properly and is not misaligned.
The friction coefficient of the hub is a complex process. When the hub is off-center, the center moves in predictable but irregular motion. Moreover, when the shaft is centered, the center may oscillate between being centered and being off-center. To compensate for this, the torque must be adequate to keep the shaft in its axis during all rotation angles. While straight-sided splines provide similar centering, they have lower misalignment load factors.
splineshaft

Keyed shafts

Essentially, splined shafts have teeth or ridges that fit together to transfer torque. Because splines are not as tall as involute gears, they offer uniform torque transfer. Additionally, they provide the opportunity for torque and rotational changes and improve wear resistance. In addition to their durability, splined shafts are popular in the aerospace industry and provide increased reliability and fatigue life.
Keyed shafts are available in different materials, lengths, and diameters. When used in high-power drive applications, they offer higher torque and rotational speeds. The higher torque they produce helps them deliver power to the gearbox. However, they are not as durable as splined shafts, which is why the latter is usually preferred in these applications. And while they’re more expensive, they’re equally effective when it comes to torque delivery.
Parallel keyed shafts have separate profiles and ridges and are used in applications requiring accuracy and precision. Keyed shafts with rolled splines are 35% stronger than cut splines and are used where precision is essential. These splines also have a smooth finish, which can make them a good choice for precision applications. They also work well with gears and other mechanical systems that require accurate torque transfer.
Carbon steel is another material used for splined shafts. Carbon steel is known for its malleability, and its shallow carbon content helps create reliable motion. However, if you’re looking for something more durable, consider ferrous steel. This type contains metals such as nickel, chromium, and molybdenum. And it’s important to remember that carbon steel is not the only material to consider.

China high quality Hot Rolling Mandrel Segment     with Best SalesChina high quality Hot Rolling Mandrel Segment     with Best Sales